Pipe unclogging with baking soda is one of the low-cost, fast, and immediate methods for unclogging the bathroom, kitchen, and toilet sewer pipes at home. This substance can be considered the strongest natural pipe opener solution that does not pose any danger to humans and sewer pipes.
Baking soda is a raw material that can be found in most kitchens today to unclog the sewer pipe, open the dishwasher pipe with baking soda, and use it to open the sewer pipe with baking soda. You can open the toilet well by making this solution.
The most common sewer blockages are due to the presence of oil and fat, which can be solved by unclogging the pipe with baking soda. In the bathroom, hair is considered a main factor for clogging the pipes.
Baking soda or sodium bicarbonate is a natural mineral compound. Alkaline powder with a little acid property that can dissolve fat in itself.
In addition, baking soda has antiseptic properties that can destroy fungi and bacteria.
It is not recommended to use acid or chemical solutions to remove clogging. These substances are very dangerous and in addition to piercing the sewer pipes, they burn the skin, eyes and nose of humans. Instead of these materials, the best thing to do at home is to open the pipe with baking soda.
Also, the use of an acid pipe opener does not guarantee the removal of cement, sand, and sand inside the pipe.
Before using the chemical solution, it is better to buy a pack of baking soda from the nearest store.
Important points before using the method of opening the sewer pipe with baking soda
Be sure to pay attention to the following points before using or during pipe unclogging with baking soda:
- In no case, do not combine the amount of materials used more than the allowed limit, because there is a possibility of gas release due to the combination of two alkaline and basic substances, namely vinegar and baking soda.
- If you have poured acid into the sewer pipe, do not use the pipe opener solution with baking soda after that.
- You can use this solution to unclog the toilet, bathroom and kitchen, as well as unclog the dishwasher pipe with baking soda.
- If the first application is not effective, you should not pour this solution into the tube more than twice.
- If the pipe does not open after two steps, the blockage is severe and you should use the spring service.
How to open a sewer pipe with baking soda
How to open a sewer pipe with baking soda is to first pour 1 cup of baking soda into the sewer pipe, then immediately pour a glass of vinegar into the pipe. After doing this, wait for about 1 hour until the waste inside the pipe is washed and removed. Now pour a kettle of boiling water into the tube.
Note: The amount of baking soda and vinegar depends on the severity of the blockage.
In the following, you can read in general with complete explanations how to open the sewer pipe with baking soda.
Whenever you feel that the water drains hard or slowly while using the sink, toilet or bathroom, use the baking soda unclogging method to prevent severe clogs.
What you need
- Hot water
- Dishwashing Liquid
- baking soda
- white vinegar
- Salt
- funnel
Now follow these steps to open the pipe with baking soda:
1- Prepare hot water
Put a kettle of water on the gas until it boils.
2- Pouring hot water and soap in the sewer pipe
Pour a little soap into the pipe (it is better to dissolve the soap in hot water and then pour it into the pipe), then empty the kettle of hot water into the pipe. (soap helps to dissolve fats)
3- Pouring baking soda
In the third step of the solution to open the pipe with baking soda, you should empty a cup or half a cup of baking soda into the sewer pipe using a funnel so that it enters the pipe completely.
4- pouring white vinegar
Pour a cup of white vinegar down the drain. Don’t be surprised by the reaction. Baking soda is an alkaline substance and vinegar is dilute acetic acid, and the combination of these two will naturally cause a reaction.
When these two substances are combined, they try to neutralize each other and therefore a chemical reaction occurs. A reaction that causes fats to dissolve and relieve congestion.
5- Pouring hot water
To wash the sewer pipe and completely dissolve the fats, empty the hot water into the sewer pipe again.
If you have done all these steps and there is no result, repeat all the steps of unclogging with baking soda at least one or two more times. If you still don’t get the result, we suggest you look for someone who works in the field of plumbing in Toronto.